dmesg - mesa5 pc2
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Initializing cgroup subsys cpuacct
Linux version 3.16.0-59-generic (buildd@lgw01-51) (gcc version 4.8.2 (Ubuntu 4.8.2-19ubuntu1) ) #79~14.04.1-Ubuntu SMP Mon Jan 18 15:41:27 UTC 2016 (Ubuntu 3.16.0-59.79~14.04.1-generic 3.16.7-ckt20)
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
e820: BIOS-provided physical RAM map:
BIOS-e820: [mem 0x0000000000000000-0x000000000009f7ff] usable
BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved
BIOS-e820: [mem 0x00000000000e6000-0x00000000000fffff] reserved
BIOS-e820: [mem 0x0000000000100000-0x00000000cf6affff] usable
BIOS-e820: [mem 0x00000000cf6b0000-0x00000000cf6bffff] ACPI data
BIOS-e820: [mem 0x00000000cf6c0000-0x00000000cf6effff] ACPI NVS
BIOS-e820: [mem 0x00000000cf6f0000-0x00000000cf6fffff] reserved
BIOS-e820: [mem 0x00000000fed00000-0x00000000fed003ff] reserved
BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
BIOS-e820: [mem 0x00000000ff380000-0x00000000ffffffff] reserved
NX (Execute Disable) protection: active
SMBIOS 2.4 present.
DMI: To Be Filled By O.E.M. To Be Filled By O.E.M./G31M-GS. , BIOS P1.90 05/16/2012
e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
e820: remove [mem 0x000a0000-0x000fffff] usable
AGP: No AGP bridge found
e820: last_pfn = 0xcf6b0 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CBFFF write-protect
CC000-DFFFF uncachable
E0000-EFFFF write-through
F0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 base 080000000 mask FC0000000 write-back
2 base 0C0000000 mask FF0000000 write-back
3 base 0CF700000 mask FFFF00000 uncachable
4 base 0CF800000 mask FFF800000 uncachable
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
original variable MTRRs
reg 0, base: 0GB, range: 2GB, type WB
reg 1, base: 2GB, range: 1GB, type WB
reg 2, base: 3GB, range: 256MB, type WB
reg 3, base: 3319MB, range: 1MB, type UC
reg 4, base: 3320MB, range: 8MB, type UC
total RAM covered: 3319M
Found optimal setting for mtrr clean up
gran_size: 64K chunk_size: 16M num_reg: 5 lose cover RAM: 0G
New variable MTRRs
reg 0, base: 0GB, range: 2GB, type WB
reg 1, base: 2GB, range: 1GB, type WB
reg 2, base: 3GB, range: 256MB, type WB
reg 3, base: 3319MB, range: 1MB, type UC
reg 4, base: 3320MB, range: 8MB, type UC
found SMP MP-table at [mem 0x000ff780-0x000ff78f] mapped at [ffff8800000ff780]
Scanning 1 areas for low memory corruption
Base memory trampoline at [ffff880000099000] 99000 size 24576
init_memory_mapping: [mem 0x00000000-0x000fffff]
[mem 0x00000000-0x000fffff] page 4k
BRK [0x01fbf000, 0x01fbffff] PGTABLE
BRK [0x01fc0000, 0x01fc0fff] PGTABLE
BRK [0x01fc1000, 0x01fc1fff] PGTABLE
init_memory_mapping: [mem 0xcf400000-0xcf5fffff]
[mem 0xcf400000-0xcf5fffff] page 2M
BRK [0x01fc2000, 0x01fc2fff] PGTABLE
init_memory_mapping: [mem 0xcc000000-0xcf3fffff]
[mem 0xcc000000-0xcf3fffff] page 2M
init_memory_mapping: [mem 0x80000000-0xcbffffff]
[mem 0x80000000-0xcbffffff] page 2M
BRK [0x01fc3000, 0x01fc3fff] PGTABLE
init_memory_mapping: [mem 0x00100000-0x7fffffff]
[mem 0x00100000-0x001fffff] page 4k
[mem 0x00200000-0x7fffffff] page 2M
init_memory_mapping: [mem 0xcf600000-0xcf6affff]
[mem 0xcf600000-0xcf6affff] page 4k
BRK [0x01fc4000, 0x01fc4fff] PGTABLE
RAMDISK: [mem 0x35ad6000-0x36d62fff]
ACPI: Early table checksum verification disabled
ACPI: RSDP 0x00000000000FA010 000014 (v00 ACPIAM)
ACPI: RSDT 0x00000000CF6B0000 000040 (v01 051612 RSDT2046 20120516 MSFT 00000097)
ACPI: FACP 0x00000000CF6B0200 000084 (v01 A M I OEMFACP 12000601 MSFT 00000097)
ACPI: DSDT 0x00000000CF6B0440 0056D0 (v01 AS166 AS166181 00000181 INTL 20051117)
ACPI: FACS 0x00000000CF6C0000 000040
ACPI: APIC 0x00000000CF6B0390 00006C (v01 051612 APIC2046 20120516 MSFT 00000097)
ACPI: MCFG 0x00000000CF6B0400 00003C (v01 051612 OEMMCFG 20120516 MSFT 00000097)
ACPI: OEMB 0x00000000CF6C0040 000072 (v01 051612 OEMB2046 20120516 MSFT 00000097)
ACPI: AAFT 0x00000000CF6B5B10 000027 (v01 051612 OEMAAFT 20120516 MSFT 00000097)
ACPI: GSCI 0x00000000CF6C00C0 002024 (v01 051612 GMCHSCI 20120516 MSFT 00000097)
ACPI: SSDT 0x00000000CF6C2A10 000A7C (v01 DpgPmm CpuPm 00000012 INTL 20051117)
ACPI: Local APIC address 0xfee00000
No NUMA configuration found
Faking a node at [mem 0x0000000000000000-0x00000000cf6affff]
Initmem setup node 0 [mem 0x00000000-0xcf6affff]
NODE_DATA [mem 0xcf6ab000-0xcf6affff]
[ffffea0000000000-ffffea00033fffff] PMD -> [ffff8800cb800000-ffff8800cebfffff] on node 0
Zone ranges:
DMA [mem 0x00001000-0x00ffffff]
DMA32 [mem 0x01000000-0xffffffff]
Normal empty
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00001000-0x0009efff]
node 0: [mem 0x00100000-0xcf6affff]
On node 0 totalpages: 849486
DMA zone: 64 pages used for memmap
DMA zone: 21 pages reserved
DMA zone: 3998 pages, LIFO batch:0
DMA32 zone: 13211 pages used for memmap
DMA32 zone: 845488 pages, LIFO batch:31
Reserving Intel graphics stolen memory at 0xcf800000-0xcfffffff
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
smpboot: Allowing 4 CPUs, 2 hotplug CPUs
nr_irqs_gsi: 40
PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
PM: Registered nosave memory: [mem 0x000a0000-0x000e5fff]
PM: Registered nosave memory: [mem 0x000e6000-0x000fffff]
e820: [mem 0xd0000000-0xfecfffff] available for PCI devices
Booting paravirtualized kernel on bare hardware
setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 27 pages/cpu @ffff8800cf200000 s81408 r8192 d20992 u524288
pcpu-alloc: s81408 r8192 d20992 u524288 alloc=1*2097152
pcpu-alloc: [0] 0 1 2 3
Built 1 zonelists in Node order, mobility grouping on. Total pages: 836190
Policy zone: DMA32
PID hash table entries: 4096 (order: 3, 32768 bytes)
xsave: enabled xstate_bv 0x3, cntxt size 0x240
AGP: Checking aperture...
AGP: No AGP bridge found
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 3308760K/3397944K available (7640K kernel code, 1132K rwdata, 3616K rodata, 1356K init, 1300K bss, 89184K reserved)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
RCU dyntick-idle grace-period acceleration is enabled.
RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
Offload RCU callbacks from all CPUs
Offload RCU callbacks from CPUs: 0-3.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
NR_IRQS:16640 nr_irqs:712 16
vt handoff: transparent VT on vt#7
Console: colour dummy device 80x25
console [tty0] enabled
allocated 13631488 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
tsc: Fast TSC calibration using PIT
tsc: Detected 2592.862 MHz processor
Calibrating delay loop (skipped), value calculated using timer frequency.. 5185.72 BogoMIPS (lpj=10371448)
pid_max: default: 32768 minimum: 301
ACPI: Core revision 20140424
ACPI: All ACPI Tables successfully acquired
Security Framework initialized
AppArmor: AppArmor initialized
Yama: becoming mindful.
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
Initializing cgroup subsys blkio
Initializing cgroup subsys perf_event
Initializing cgroup subsys net_prio
Initializing cgroup subsys hugetlb
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring enabled (TM2)
process: using mwait in idle threads
Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32, 1GB 0
tlb_flushall_shift: -1
Freeing SMP alternatives memory: 32K (ffffffff81e70000 - ffffffff81e78000)
ftrace: allocating 29288 entries in 115 pages
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
smpboot: CPU0: Intel Pentium(R) Dual-Core CPU E5300 @ 2.60GHz (fam: 06, model: 17, stepping: 0a)
Performance Events: PEBS fmt0+, 4-deep LBR, Core2 events, Intel PMU driver.
... version: 2
... bit width: 40
... generic registers: 2
... value mask: 000000ffffffffff
... max period: 000000007fffffff
... fixed-purpose events: 3
... event mask: 0000000700000003
x86: Booting SMP configuration:
.... node #0, CPUs: #1
x86: Booted up 1 node, 2 CPUs
smpboot: Total of 2 processors activated (10371.44 BogoMIPS)
NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
devtmpfs: initialized
evm: security.selinux
evm: security.SMACK64
evm: security.SMACK64EXEC
evm: security.SMACK64TRANSMUTE
evm: security.SMACK64MMAP
evm: security.ima
evm: security.capability
PM: Registering ACPI NVS region [mem 0xcf6c0000-0xcf6effff] (196608 bytes)
pinctrl core: initialized pinctrl subsystem
regulator-dummy: no parameters
RTC time: 15:34:32, date: 01/28/16
NET: Registered protocol family 16
cpuidle: using governor ladder
cpuidle: using governor menu
ACPI: bus type PCI registered
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: not using MMCONFIG
PCI: Using configuration type 1 for base access
ACPI: Added _OSI(Module Device)
ACPI: Added _OSI(Processor Device)
ACPI: Added _OSI(3.0 _SCP Extensions)
ACPI: Added _OSI(Processor Aggregator Device)
ACPI: Executed 1 blocks of module-level executable AML code
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFF8800CA259800 000277 (v01 DpgPmm P001Ist 00000011 INTL 20051117)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFF8800CA259C00 000277 (v01 DpgPmm P002Ist 00000012 INTL 20051117)
ACPI: Interpreter enabled
ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140424/hwxface-580)
ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S3_] (20140424/hwxface-580)
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
acpi PNP0A08:00: _OSC: platform does not support [PCIeHotplug]
acpi PNP0A08:00: _OSC: OS now controls [PME AER PCIeCapability]
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff]
pci_bus 0000:00: root bus resource [mem 0xcf700000-0xdfffffff]
pci_bus 0000:00: root bus resource [mem 0xf0000000-0xffffffff]
pci 0000:00:00.0: [8086:29c0] type 00 class 0x060000
pci 0000:00:02.0: [8086:29c2] type 00 class 0x030000
pci 0000:00:02.0: reg 0x10: [mem 0xfea80000-0xfeafffff]
pci 0000:00:02.0: reg 0x14: [io 0xdc00-0xdc07]
pci 0000:00:02.0: reg 0x18: [mem 0xd0000000-0xdfffffff pref]
pci 0000:00:02.0: reg 0x1c: [mem 0xfe900000-0xfe9fffff]
pci 0000:00:1b.0: [8086:27d8] type 00 class 0x040300
pci 0000:00:1b.0: reg 0x10: [mem 0xfea78000-0xfea7bfff 64bit]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: System wakeup disabled by ACPI
pci 0000:00:1c.0: [8086:27d0] type 01 class 0x060400
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: System wakeup disabled by ACPI
pci 0000:00:1c.1: [8086:27d2] type 01 class 0x060400
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: System wakeup disabled by ACPI
pci 0000:00:1d.0: [8086:27c8] type 00 class 0x0c0300
pci 0000:00:1d.0: reg 0x20: [io 0xd400-0xd41f]
pci 0000:00:1d.0: System wakeup disabled by ACPI
pci 0000:00:1d.1: [8086:27c9] type 00 class 0x0c0300
pci 0000:00:1d.1: reg 0x20: [io 0xd480-0xd49f]
pci 0000:00:1d.1: System wakeup disabled by ACPI
pci 0000:00:1d.2: [8086:27ca] type 00 class 0x0c0300
pci 0000:00:1d.2: reg 0x20: [io 0xd800-0xd81f]
pci 0000:00:1d.2: System wakeup disabled by ACPI
pci 0000:00:1d.3: [8086:27cb] type 00 class 0x0c0300
pci 0000:00:1d.3: reg 0x20: [io 0xd880-0xd89f]
pci 0000:00:1d.3: System wakeup disabled by ACPI
pci 0000:00:1d.7: [8086:27cc] type 00 class 0x0c0320
pci 0000:00:1d.7: reg 0x10: [mem 0xfea77c00-0xfea77fff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: System wakeup disabled by ACPI
pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
pci 0000:00:1e.0: System wakeup disabled by ACPI
pci 0000:00:1f.0: [8086:27b8] type 00 class 0x060100
pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
pci 0000:00:1f.0: can't claim BAR 13 [io 0x0800-0x087f]: address conflict with ACPI CPU throttle [io 0x0810-0x0815]
pci 0000:00:1f.0: quirk: [io 0x0480-0x04bf] claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0280 (mask 00ff)
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0300 (mask 003f)
pci 0000:00:1f.1: [8086:27df] type 00 class 0x01018a
pci 0000:00:1f.1: reg 0x10: [io 0x0000-0x0007]
pci 0000:00:1f.1: reg 0x14: [io 0x0000-0x0003]
pci 0000:00:1f.1: reg 0x18: [io 0x08f0-0x08f7]
pci 0000:00:1f.1: reg 0x1c: [io 0x08f8-0x08fb]
pci 0000:00:1f.1: reg 0x20: [io 0xffa0-0xffaf]
pci 0000:00:1f.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
pci 0000:00:1f.1: legacy IDE quirk: reg 0x14: [io 0x03f6]
pci 0000:00:1f.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
pci 0000:00:1f.1: legacy IDE quirk: reg 0x1c: [io 0x0376]
pci 0000:00:1f.2: [8086:27c0] type 00 class 0x01018f
pci 0000:00:1f.2: reg 0x10: [io 0xd080-0xd087]
pci 0000:00:1f.2: reg 0x14: [io 0xd000-0xd003]
pci 0000:00:1f.2: reg 0x18: [io 0xcc00-0xcc07]
pci 0000:00:1f.2: reg 0x1c: [io 0xc880-0xc883]
pci 0000:00:1f.2: reg 0x20: [io 0xc800-0xc80f]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500
pci 0000:00:1f.3: reg 0x20: [io 0x0400-0x041f]
pci 0000:00:1c.0: PCI bridge to [bus 02]
pci 0000:00:1c.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref]
pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000
pci 0000:01:00.0: reg 0x10: [io 0xe800-0xe8ff]
pci 0000:01:00.0: reg 0x18: [mem 0xfdeff000-0xfdefffff 64bit pref]
pci 0000:01:00.0: reg 0x20: [mem 0xfdef8000-0xfdefbfff 64bit pref]
pci 0000:01:00.0: supports D1 D2
pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:1c.1: PCI bridge to [bus 01]
pci 0000:00:1c.1: bridge window [io 0xe000-0xefff]
pci 0000:00:1c.1: bridge window [mem 0xfde00000-0xfdefffff 64bit pref]
pci 0000:03:02.0: [168c:002d] type 00 class 0x028000
pci 0000:03:02.0: reg 0x10: [mem 0xfebf0000-0xfebfffff]
pci 0000:00:1e.0: PCI bridge to [bus 03] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0xfeb00000-0xfebfffff]
pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0x000d0000-0x000dffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0xcf700000-0xdfffffff] (subtractive decode)
pci 0000:00:1e.0: bridge window [mem 0xf0000000-0xffffffff] (subtractive decode)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: Enabled 2 GPEs in block 00 to 1F
vgaarb: setting as boot device: PCI:0000:00:02.0
vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
vgaarb: bridge control possible 0000:00:02.0
SCSI subsystem initialized
libata version 3.00 loaded.
ACPI: bus type USB registered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
e820: reserve RAM buffer [mem 0x0009f800-0x0009ffff]
e820: reserve RAM buffer [mem 0xcf6b0000-0xcfffffff]
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 comparators, 64-bit 14.318180 MHz counter
Switched to clocksource hpet
AppArmor: AppArmor Filesystem Enabled
pnp: PnP ACPI init
ACPI: bus type PNP registered
system 00:00: [mem 0xfed14000-0xfed19fff] has been reserved
system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:02: [dma 3]
pnp 00:02: Plug and Play ACPI device, IDs PNP0401 (active)
system 00:03: [io 0x04d0-0x04d1] has been reserved
system 00:03: [io 0x0800-0x087f] could not be reserved
system 00:03: [io 0x0480-0x04bf] has been reserved
system 00:03: [io 0x0900-0x090f] has been reserved
system 00:03: [mem 0xfed1c000-0xfed1ffff] has been reserved
system 00:03: [mem 0xfed20000-0xfed8ffff] has been reserved
system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
system 00:04: [mem 0xffc00000-0xfff7ffff] has been reserved
system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
system 00:05: [mem 0xfec00000-0xfec00fff] could not be reserved
system 00:05: [mem 0xfee00000-0xfee00fff] has been reserved
system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:06: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active)
pnp 00:07: [dma 0 disabled]
pnp 00:07: Plug and Play ACPI device, IDs PNP0501 (active)
system 00:08: [io 0x0280-0x028f] has been reserved
system 00:08: [io 0x0290-0x029f] has been reserved
system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
system 00:09: [mem 0xe0000000-0xefffffff] has been reserved
system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
system 00:0a: [mem 0x00000000-0x0009ffff] could not be reserved
system 00:0a: [mem 0x000e0000-0x000fffff] could not be reserved
system 00:0a: [mem 0x00100000-0xcf6fffff] could not be reserved
system 00:0a: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp: PnP ACPI: found 11 devices
ACPI: bus type PNP unregistered
pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 02] add_size 1000
pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 02] add_size 400000
pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff] to [bus 01] add_size 400000
pci 0000:00:1f.0: BAR 13: [io 0x0800-0x087f] has bogus alignment
pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 400000
pci 0000:00:1c.1: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 400000
pci 0000:00:1c.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
pci 0000:00:1c.0: BAR 14: assigned [mem 0xf0000000-0xf03fffff]
pci 0000:00:1c.1: BAR 14: assigned [mem 0xf0400000-0xf07fffff]
pci 0000:00:1c.0: BAR 13: assigned [io 0x1000-0x1fff]
pci 0000:00:1c.0: PCI bridge to [bus 02]
pci 0000:00:1c.0: bridge window [io 0x1000-0x1fff]
pci 0000:00:1c.0: bridge window [mem 0xf0000000-0xf03fffff]
pci 0000:00:1c.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref]
pci 0000:00:1c.1: PCI bridge to [bus 01]
pci 0000:00:1c.1: bridge window [io 0xe000-0xefff]
pci 0000:00:1c.1: bridge window [mem 0xf0400000-0xf07fffff]
pci 0000:00:1c.1: bridge window [mem 0xfde00000-0xfdefffff 64bit pref]
pci 0000:00:1e.0: PCI bridge to [bus 03]
pci 0000:00:1e.0: bridge window [mem 0xfeb00000-0xfebfffff]
pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
pci_bus 0000:00: resource 8 [mem 0xcf700000-0xdfffffff]
pci_bus 0000:00: resource 9 [mem 0xf0000000-0xffffffff]
pci_bus 0000:02: resource 0 [io 0x1000-0x1fff]
pci_bus 0000:02: resource 1 [mem 0xf0000000-0xf03fffff]
pci_bus 0000:02: resource 2 [mem 0xfdf00000-0xfdffffff 64bit pref]
pci_bus 0000:01: resource 0 [io 0xe000-0xefff]
pci_bus 0000:01: resource 1 [mem 0xf0400000-0xf07fffff]
pci_bus 0000:01: resource 2 [mem 0xfde00000-0xfdefffff 64bit pref]
pci_bus 0000:03: resource 1 [mem 0xfeb00000-0xfebfffff]
pci_bus 0000:03: resource 4 [io 0x0000-0x0cf7]
pci_bus 0000:03: resource 5 [io 0x0d00-0xffff]
pci_bus 0000:03: resource 6 [mem 0x000a0000-0x000bffff]
pci_bus 0000:03: resource 7 [mem 0x000d0000-0x000dffff]
pci_bus 0000:03: resource 8 [mem 0xcf700000-0xdfffffff]
pci_bus 0000:03: resource 9 [mem 0xf0000000-0xffffffff]
NET: Registered protocol family 2
TCP established hash table entries: 32768 (order: 6, 262144 bytes)
TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP: reno registered
UDP hash table entries: 2048 (order: 4, 65536 bytes)
UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
NET: Registered protocol family 1
pci 0000:00:02.0: Video device with shadowed ROM
PCI: CLS 32 bytes, default 64
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 18996K (ffff880035ad6000 - ffff880036d63000)
microcode: CPU0 sig=0x1067a, pf=0x1, revision=0xa07
microcode: CPU1 sig=0x1067a, pf=0x1, revision=0xa07
microcode: Microcode Update Driver: v2.00 , Peter Oruba
Scanning for low memory corruption every 60 seconds
futex hash table entries: 1024 (order: 4, 65536 bytes)
Initialise system trusted keyring
audit: initializing netlink subsys (disabled)
audit: type=2000 audit(1453995272.472:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
zpool: loaded
zbud: loaded
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
fuse init (API version 7.23)
msgmni has been set to 6499
Key type big_key registered
Key type asymmetric registered
Asymmetric key parser 'x509' registered
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
pcieport 0000:00:1c.0: enabling device (0106 -> 0107)
pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt
pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
vesafb: mode is 1280x1024x32, linelength=5120, pages=0
vesafb: scrolling: redraw
vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90010780000, using 5120k, total 5120k
Console: switching to colour frame buffer device 160x64
fb0: VESA VGA frame buffer device
intel_idle: does not run on family 6 model 23
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
ACPI: Power Button [PWRF]
GHES: HEST is not enabled!
00:07: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel G33 Chipset
agpgart-intel 0000:00:00.0: detected gtt size: 524288K total, 262144K mappable
agpgart-intel 0000:00:00.0: detected 8192K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
brd: module loaded
loop: module loaded
ata_piix 0000:00:1f.1: version 2.13
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
scsi2 : ata_piix
scsi3 : ata_piix
ata3: SATA max UDMA/133 cmd 0xd080 ctl 0xd000 bmdma 0xc800 irq 19
ata4: SATA max UDMA/133 cmd 0xcc00 ctl 0xc880 bmdma 0xc808 irq 19
libphy: Fixed MDIO Bus: probed
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
PPP generic driver version 2.4.2
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-pci 0000:00:1d.7: EHCI Host Controller
ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci-pci 0000:00:1d.7: debug port 1
ehci-pci 0000:00:1d.7: cache line size of 32 is not supported
ehci-pci 0000:00:1d.7: irq 23, io mem 0xfea77c00
ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 3.16.0-59-generic ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ehci-platform: EHCI generic platform driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-pci: OHCI PCI platform driver
ohci-platform: OHCI generic platform driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: detected 2 ports
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000d400
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 3.16.0-59-generic uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: detected 2 ports
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d480
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 3.16.0-59-generic uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: detected 2 ports
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d800
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 3.16.0-59-generic uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: detected 2 ports
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d880
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 3.16.0-59-generic uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
i8042: PNP: PS/2 Controller [PNP0f03:PS2M] at 0x60,0x64 irq 12
i8042: PNP: PS/2 controller doesn't have KBD irq; using default 1
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mousedev: PS/2 mouse device common for all mice
rtc_cmos 00:01: RTC can wake from S4
rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
rtc_cmos 00:01: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
ledtrig-cpu: registered to indicate activity on CPUs
TCP: cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
Key type dns_resolver registered
Loading compiled-in X.509 certificates
Loaded X.509 cert 'Magrathea: Glacier signing key: db812a9edbedcecb54fc9fd82a4b24b6a89b4e9d'
registered taskstats version 1
Key type trusted registered
Key type encrypted registered
AppArmor: AppArmor sha1 policy hashing enabled
ima: No TPM chip found, activating TPM-bypass!
evm: HMAC attrs: 0x1
Magic number: 0:693:589
rtc_cmos 00:01: setting system clock to 2016-01-28 15:34:33 UTC (1453995273)
BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
EDD information not available.
PM: Hibernation image not present or could not be loaded.
ata4.00: ATA-8: ST3250318AS, CC38, max UDMA/133
ata4.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata4.00: configured for UDMA/133
ata3.00: ATA-8: ST500DM002-1BD142, KC48, max UDMA/133
ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata3.01: ATAPI: HL-DT-ST DVDRAM GH22NS50, TN02, max UDMA/100
ata3.00: configured for UDMA/133
ata3.01: configured for UDMA/100
scsi 2:0:0:0: Direct-Access ATA ST500DM002-1BD14 KC48 PQ: 0 ANSI: 5
sd 2:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 2:0:0:0: [sda] 4096-byte physical blocks
sd 2:0:0:0: Attached scsi generic sg0 type 0
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
scsi 2:0:1:0: CD-ROM HL-DT-ST DVDRAM GH22NS50 TN02 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
cdrom: Uniform CD-ROM driver Revision: 3.20
sr 2:0:1:0: Attached scsi CD-ROM sr0
sr 2:0:1:0: Attached scsi generic sg1 type 5
scsi 3:0:0:0: Direct-Access ATA ST3250318AS CC38 PQ: 0 ANSI: 5
sd 3:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 3:0:0:0: Attached scsi generic sg2 type 0
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
sd 2:0:0:0: [sda] Attached SCSI disk
sdb: sdb1 sdb2
sd 3:0:0:0: [sdb] Attached SCSI disk
Freeing unused kernel memory: 1356K (ffffffff81d1d000 - ffffffff81e70000)
Write protecting the kernel read-only data: 12288k
Freeing unused kernel memory: 540K (ffff880001779000 - ffff880001800000)
Freeing unused kernel memory: 480K (ffff880001b88000 - ffff880001c00000)
systemd-udevd[118]: starting version 204
Floppy drive(s): fd0 is 1.44M
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:01:00.0: irq 42 for MSI/MSI-X
r8169 0000:01:00.0 eth0: RTL8168d/8111d at 0xffffc90010768000, d0:50:99:36:c6:6d, XID 081000c0 IRQ 42
r8169 0000:01:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
usb 3-2: new low-speed USB device number 2 using uhci_hcd
usb 3-2: New USB device found, idVendor=1c4f, idProduct=0002
usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-2: Product: USB Keykoard
usb 3-2: Manufacturer: USB
hidraw: raw HID events driver (C) Jiri Kosina
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
input: USB USB Keykoard as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.0/0003:1C4F:0002.0001/input/input5
hid-generic 0003:1C4F:0002.0001: input,hidraw0: USB HID v1.10 Keyboard [USB USB Keykoard] on usb-0000:00:1d.1-2/input0
input: USB USB Keykoard as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.1/0003:1C4F:0002.0002/input/input6
hid-generic 0003:1C4F:0002.0002: input,hidraw1: USB HID v1.10 Device [USB USB Keykoard] on usb-0000:00:1d.1-2/input1
psmouse serio1: alps: Unknown ALPS touchpad: E7=10 00 64, EC=10 00 64
tsc: Refined TSC clocksource calibration: 2592.820 MHz
EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input4
Switched to clocksource tsc
floppy0: no floppy controllers found
random: nonblocking pool is initialized
Adding 4194300k swap on /dev/sda1. Priority:-1 extents:1 across:4194300k FS
systemd-udevd[286]: starting version 204
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
parport_pc 00:02: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
lp0: using parport0 (interrupt-driven).
EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
Floppy drive(s): fd0 is 1.44M
intel_rng: FWH not detected
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI Warning: SystemIO range 0x0000000000000828-0x000000000000082F conflicts with OpRegion 0x0000000000000800-0x000000000000084F (\PMRG) (20140424/utaddress-254)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
ACPI Warning: SystemIO range 0x0000000000000480-0x00000000000004AF conflicts with OpRegion 0x0000000000000480-0x00000000000004AF (\GPR2) (20140424/utaddress-254)
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
lpc_ich: Resource conflict(s) found affecting gpio_ich
leds_ss4200: no LED devices found
[drm] Initialized drm 1.1.0 20060810
EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null)
cfg80211: Calling CRDA to update world regulatory domain
snd_hda_intel 0000:00:1b.0: irq 43 for MSI/MSI-X
[drm] Memory usable by graphics device = 512M
checking generic (d0000000 500000) vs hw (d0000000 10000000)
fb: switching to inteldrmfb from VESA VGA
Console: switching to colour dummy device 80x25
[drm] Replacing VGA console driver
gpio_ich: GPIO from 206 to 255 on gpio_ich
i915 0000:00:02.0: irq 44 for MSI/MSI-X
[drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[drm] Driver supports precise vblank timestamp query.
vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[drm] initialized overlay support
sound hdaudioC0D0: autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
sound hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
sound hdaudioC0D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
sound hdaudioC0D0: mono: mono_out=0x0
sound hdaudioC0D0: inputs:
sound hdaudioC0D0: Front Mic=0x19
sound hdaudioC0D0: Rear Mic=0x18
sound hdaudioC0D0: Line=0x1a
input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
input: HDA Intel Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 160x64
i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
i915 0000:00:02.0: registered panic notifier
i915: No ACPI video bus found
[drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
ath: EEPROM regdomain: 0x809c
ath: EEPROM indicates we should expect a country code
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x52
ath: Country alpha2 being used: CN
ath: Regpair used: 0x52
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xffffc90010820000, irq=23
cfg80211: Calling CRDA to update world regulatory domain
floppy0: no floppy controllers found
work still pending
cfg80211: World regulatory domain updated:
cfg80211: DFS Master region: unset
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: Calling CRDA for country: CN
cfg80211: Regulatory domain changed to country: CN
cfg80211: DFS Master region: unset
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
cfg80211: (57240000 KHz - 59400000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
cfg80211: (59400000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4400 mBm), (N/A)
cfg80211: (63720000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
audit: type=1400 audit(1453995286.174:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=420 comm="apparmor_parser"
audit: type=1400 audit(1453995286.174:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=420 comm="apparmor_parser"
audit: type=1400 audit(1453995286.174:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=420 comm="apparmor_parser"
audit: type=1400 audit(1453995286.174:5): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=420 comm="apparmor_parser"
audit: type=1400 audit(1453995286.174:6): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=420 comm="apparmor_parser"
audit: type=1400 audit(1453995286.174:7): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=420 comm="apparmor_parser"
audit: type=1400 audit(1453995286.174:8): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=544 comm="apparmor_parser"
audit: type=1400 audit(1453995286.174:9): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=544 comm="apparmor_parser"
audit: type=1400 audit(1453995286.174:10): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=544 comm="apparmor_parser"
audit: type=1400 audit(1453995286.174:11): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=418 comm="apparmor_parser"
init: failsafe main process (646) killed by TERM signal
Bluetooth: Core ver 2.19
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: BNEP socket layer initialized
init: cups main process (803) killed by HUP signal
init: cups main process ended, respawning
audit_printk_skb: 42 callbacks suppressed
audit: type=1400 audit(1453995296.174:26): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=997 comm="apparmor_parser"
audit: type=1400 audit(1453995296.174:27): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=997 comm="apparmor_parser"
audit: type=1400 audit(1453995296.174:28): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=997 comm="apparmor_parser"
audit: type=1400 audit(1453995296.174:29): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=997 comm="apparmor_parser"
audit: type=1400 audit(1453995296.174:30): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=997 comm="apparmor_parser"
audit: type=1400 audit(1453995296.174:31): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=997 comm="apparmor_parser"
audit: type=1400 audit(1453995296.318:32): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cups-browsed" pid=999 comm="apparmor_parser"
audit: type=1400 audit(1453995296.322:33): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=1000 comm="apparmor_parser"
audit: type=1400 audit(1453995296.322:34): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=1000 comm="apparmor_parser"
audit: type=1400 audit(1453995296.322:35): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=1000 comm="apparmor_parser"
r8169 0000:01:00.0 eth0: link down
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
init: samba-ad-dc main process (908) terminated with status 1
wlan0: authenticate with 00:15:6d:4e:af:71
wlan0: send auth to 00:15:6d:4e:af:71 (try 1/3)
wlan0: authenticated
wlan0: associate with 00:15:6d:4e:af:71 (try 1/3)
wlan0: RX AssocResp from 00:15:6d:4e:af:71 (capab=0x421 status=0 aid=14)
wlan0: associated
IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
wlan0: deauthenticating from 00:15:6d:4e:af:71 by local choice (Reason: 2=PREV_AUTH_NOT_VALID)
cfg80211: Calling CRDA to update world regulatory domain
wlan0: authenticate with 00:15:6d:4e:af:71
wlan0: send auth to 00:15:6d:4e:af:71 (try 1/3)
cfg80211: World regulatory domain updated:
cfg80211: DFS Master region: unset
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
wlan0: send auth to 00:15:6d:4e:af:71 (try 2/3)
wlan0: authenticated
wlan0: authenticate with 00:15:6d:4e:af:71
wlan0: send auth to 00:15:6d:4e:af:71 (try 1/3)
wlan0: send auth to 00:15:6d:4e:af:71 (try 2/3)
wlan0: send auth to 00:15:6d:4e:af:71 (try 3/3)
wlan0: authentication with 00:15:6d:4e:af:71 timed out
wlan0: authenticate with 00:15:6d:4e:af:19
wlan0: direct probe to 00:15:6d:4e:af:19 (try 1/3)
wlan0: direct probe to 00:15:6d:4e:af:19 (try 2/3)
wlan0: direct probe to 00:15:6d:4e:af:19 (try 3/3)
wlan0: authentication with 00:15:6d:4e:af:19 timed out
wlan0: authenticate with 00:15:6d:4e:af:71
wlan0: send auth to 00:15:6d:4e:af:71 (try 1/3)
wlan0: authenticated
wlan0: associate with 00:15:6d:4e:af:71 (try 1/3)
wlan0: RX AssocResp from 00:15:6d:4e:af:71 (capab=0x421 status=0 aid=14)
wlan0: associated
init: plymouth-upstart-bridge main process ended, respawning
audit_printk_skb: 15 callbacks suppressed
audit: type=1400 audit(1453995320.897:41): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=1707 comm="apparmor_parser"
audit: type=1400 audit(1453995320.897:42): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=1707 comm="apparmor_parser"
audit: type=1400 audit(1453995320.897:43): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=1707 comm="apparmor_parser"
perf interrupt took too long (2520 > 2500), lowering kernel.perf_event_max_sample_rate to 50000
audit: type=1400 audit(1453996551.533:44): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=4271 comm="apparmor_parser"
audit: type=1400 audit(1453996551.533:45): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=4271 comm="apparmor_parser"
audit: type=1400 audit(1453996551.533:46): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=4271 comm="apparmor_parser"
wlan0: authenticate with 00:15:6d:4e:af:1f
wlan0: direct probe to 00:15:6d:4e:af:1f (try 1/3)
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211: DFS Master region: unset
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
wlan0: direct probe to 00:15:6d:4e:af:1f (try 2/3)
wlan0: send auth to 00:15:6d:4e:af:1f (try 3/3)
wlan0: authenticated
wlan0: associate with 00:15:6d:4e:af:1f (try 1/3)
wlan0: RX AssocResp from 00:15:6d:4e:af:1f (capab=0x421 status=0 aid=3)
wlan0: associated
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211: DFS Master region: unset
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
wlan0: authenticate with 00:15:6d:4e:af:71
wlan0: send auth to 00:15:6d:4e:af:71 (try 1/3)
wlan0: authenticated
wlan0: associating with AP with corrupt beacon
wlan0: associate with 00:15:6d:4e:af:71 (try 1/3)
wlan0: RX AssocResp from 00:15:6d:4e:af:71 (capab=0x421 status=0 aid=14)
wlan0: associated
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211: DFS Master region: unset
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm), (N/A)
wlan0: authenticate with 00:15:6d:4e:af:71
wlan0: send auth to 00:15:6d:4e:af:71 (try 1/3)
wlan0: authenticated
wlan0: associating with AP with corrupt beacon
wlan0: associate with 00:15:6d:4e:af:71 (try 1/3)
wlan0: RX AssocResp from 00:15:6d:4e:af:71 (capab=0x421 status=0 aid=14)
wlan0: associated